The following list is a small sample of parts currently in stock at the Register's spares store, more parts will be listed in due course. Please email the Spares Consultant, Bob Langston, to enquire about any spares required. Please note that large or heavy items may need to be collected from the stores, as they may not be able to be couriered.
The Wolseley Register Spares are sold in good faith, however, please note that all parts are sold as seen, untested and with no warranty.
The items are displayed in approximate ascending model age / model size order. Please click on image to see full size picture.
Series II 14/56 Rear Axle:
Used. Includes diff, half shafts and hubs. Unknown condition. Diff loose from axle casing, and its pinion has been removed, but is still included
Series II SuperSix 16, 21, 25 Half Shafts:
Used. Good condition. Some light surface rust.
Eight rear bump stops:
Used. Rubber perished
Eight rear spring U bolts and plates:
Used. OK
Eight / Ten outer rear hubs:
NOS and Used.
Eight / Ten rear hub carrier:
Used. Incudes bearings and seals. Look OK.
Eight / Ten Half Shafts:
Used. Length 26",
Shaft diameter = 1",
6 inner splines.
Eight / Ten Rear Axle Retaining Plate for felt seal:
NOS. 80mm ext. dia. & 55 int. dia
Series III Ten Differential:
Used. Unknown condition.
7/37 ratio.
Both square and round flanges available.
Series III Ten Crown Wheel & Pinion:
NOS.
Series II 10/40, 12/48, 14/56, 16/60,18/80
Series III 12/48, 14/60, 16/65, 18/85
Hub locking washers:
NOS.
Series II 10/40, 12/48, 14/56, 16/60,18/80
Series III 12/48, 14/60, 16/65, 18/85
Hub locking nuts:
Used. Look OK
Series II 10/40, 12/48, 14/56, 16/60,18/80
Series III 12/48, 14/60, 16/65, 18/85
rear hub bearings:
Pair lightly used. Please note - the bearings available are NOT the SKF ones pictured.
Series III 12/48 & 14/60 Diff:
Used. Ratio 9/48.
Also, an incomplete one for spares, with a good crown wheel and pinion.
Series III 12/48, 14/60 Half Shafts - early type:
Used. With 5/8" wheel stud holes. To fit early models with studs incorporating a 5/8" shoulder.
Series III 12/48 14/60 Half Shafts - later type:
Used. With 1/2" wheel stud holes.
14/60 rear hub bearing housing:
Used. Looks OK
Series III 18/85 rear hub bearing carriers:
Used. Good condition.
Series II & III rear bump stop:
Used. Surface rust, but otherwise good condition. Also fits 25DHC, but not any Supersixes.
Series III Supersix rear axle U bolts:
Used. OK
Series III 25DHC Crown wheel & pinion:
Believed NOS. Believed to fit a 25DHC - but please ask for further details
Pair 25DHC half shafts:
Used. Surface rust, but otherwise ok.
4/44 rear axle:
Used. One half shaft out, but this is available separately. Unknown condition.
4/44 Halfshaft:
Used. Complete with outer bearing. Some surface rust, but OK.
1500 Rear Axle Bump Stops:
Used.
1500 Rear Axle:
Used. Complete with hubs. Diff turns, but otherwise unknown condition.
1500 half shafts:
Used. One only left.
16/60 Diff:
Used. Crownwheel has "MOWOG-BTB-324- 10/43" on it. Casing has "ATB 7182" on it. Complete and looks OK.
6/99 6/110 Rear Axle:
Used. Complete with hubs. Diff turns, but otherwise unknown condition.
6/99 6/110 Pair Half Shafts:
Used. Look OK.
Assorted Rear Axles:
Used. All Wolseley.